MASTER FLASH®
QUALITY & SERVICE WORLDWIDE
Design Excellence
Master Flash® design meets all roofing needs. Sleeve flexibility accommodates vibration and pipe movement caused by expansion contraction. The soft aluminum base easily conforms to most metal roof profiles.
Weather Protection
Made or EPDM, these flashings are compounded specifically for maximum resistance to weathering due to ozone and ultraviolet light.
Base Flexibility
The base is designed to form a seal on most panel configurations and roof pitches regardless of pipe location.
Easy On-Site Customization
Fast, one piece construction allows for easy on-site installation usually 5 minutes.
Modification Made Simple
Easy to see pipe diameters make for painless on-site installation.
Standard Master Flash®
- 9 sizes, designed for 1/4” to 28-1/2” (6 – 723mm) diameter pipes
- Easy on-site installation in usually 5 minutes
- The soft aluminum base easily conforms to most metal roof profiles
- Pipe diameters can be seen clearly for proper pipe fitting
Extreme Angle Master Flash®
- Designed for 1/4” to 5-3/4” (6 – 146mm) diameter pipes
- Easy on-site installation in usually 5 minutes
- The built in 40º degree pitch allows to handle any extreme roof pitch (35º – 65º)
- Sleeve flexibility accommodates vibration and pipe movement caused by expansion contraction
Multi-Flash Master Flash® Two Flashings in ONE!
- 9 Sizes, designed for 1/4” to 28-1/2” (6 – 723mm) diameter pipes
- Smooth cut is intended to eliminate use of razor blades
- Stainless steel gripper to secure a retro custom fit
- Gripper available upon request
Retrofit Master Flash®
- 3 sizes, designed for 1/2” to 16-1/4” (12 – 412mm) diameter pipes
- Easy to see pipe diameters make for painless on site customization
- Easily installed fastener snaps included
Solar Multi-Port - MR Master Flash®
5 Port Design for the Metal Roofing Industry
• Accommodates:
ONE 0” – 1-15/16” (0 – 49mm) pipe
TWO 3/8” (9.6mm) pipe / cable
TWO 3/4” (20mm) pipe / cable
- 4-1/2” (114mm) base
- Up to 4 cables or wires per flashing
- Extra ports to accommodate copper pipe and electrical cabling
- Easy install for solar applications
Square Vent Master Flash®
- 2 sizes/EPDM/designed for 2-1/2” to 5” (63 – 127mm) diameter pipes
- Made to withstand the damaging effects of ultraviolet light and ozone
- Easy install snaps included, specially designed for square vent applications
- Sleeve flexibility accommodates vibration and pipe movement caused by expansion/contraction
Universal Master Flash®
- All around performance
- 9 sizes, designed for 1/4” to 19” (6 – 482mm) diameter pipes
- Easy on-site customization can accommodate all normal installations
Solar-Flash Master Flash®
- Specifically designed for solar applications
- Designed for 3/4” (19mm) to 1” (25mm) diameter pipes
- Pre-cut hole for pipe sizes 3/4” (19mm) to 1” (25mm) allowing for minimal on-site preparation and assembly
- The pitch canal allows for maximum flexibility, easily accommodating up to a 60º degree pitch without affecting performance
Universal Retrofit Master Flash®
- 3 sizes, designed for 3/4” (19mm) to 10” (254mm) diameter pipes
- Fast, one piece construction allows for easy on-site install in usually 5 minutes
* Master Flash; the only CSA Approved EPDM rubber flashing.
The only ICC listed flashing for the Metal Building Industry with a 35 year warranty
- 11 Sizes / Designed for 1 /8” to 28-1 /2” (3-723mm) diameter pipes
- On-site customization
- Designed for 1/4” to 13” (6-330mm) diameter pipes
- Pipe diameters can be seen clearly for proper pipe fitting
MASTER CLOSURE
A SUPERIOR METAL PANEL & METAL ROOF CLOSURE SYSTEM
- Master Closure is a non shrinking crosslink polyethylene foam, 2 lb. density, charcoal gray in color
- Fast, easy and economical to install in lengths to fit your profile
- Available with or without glue bead for easy installation
- Most metal profiles are available and in stock
- Configurations for outside and inside metal profiles
- Provides complete snow, rain and insect barrier
- No special tools required – simply peel and stick
- Very light weight product that is easily handled and installed
- Does not promote combustion
Technical Data:
MASTER CLOSURE PHYSICAL SPECIFICATIONS
Density: 2 pcf – no shrinkage
Elongation: 120% (% to break)
Compression set: 28% (% original thickness)
Water absorption: 0.04 – lb/sq ft
(Does not absorb water)
Tensile strength: 43 psi
Tear resistance: 11 – lbs/in2
Shore hardness (A): 7
Working temperature: -70°F to +175°F